Forums :: Resources :: Features :: Photo Gallery :: Vintage Radio Shows :: Archives :: Books
Support This Site: Contributors :: Advertise


It is currently Dec Sat 16, 2017 12:25 am


All times are UTC [ DST ]





Post New Topic Post Reply  [ 76 posts ]  Go to page Previous  1, 2, 3, 4
Author Message
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Mon 06, 2017 12:27 pm 
Member

Joined: Oct Sun 15, 2006 12:57 pm
Posts: 5319
Joe, No worries, I got it!!! Thats an early pic, a considerable amount of work was done after that one was taken. That pic was simply one of three, showing the routing of the white wire, AGC I think. This radio was a -17 and the "preferred" configuration by the guys who know, was the -10 or -14 as I remember, so I changed things accordingly while I was in there.

This radio had been "FIXED" several times across the years, and it took a lot of work to get it close to "stock". Thank goodness for the TM11-851 PUB.
Image

Norm, EXCELLENT POINT, if you cant get to'em you can't tweek'em.

My deal was that somewhere in the assembly process, I lost about 30db of sensitivity. Turned out, I had put the jumper wires from the tuning cap into the holes on the lugs of the RF deck, but didn't solder the two ( or 3?) connections for the first stage. So there was just a fraction of a pF of coupling. Only spent half an hour or so on that one. :roll:

_________________
Bold text & pics are usually links.

Mike


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Tue 07, 2017 5:34 am 
Member

Joined: Dec Mon 31, 2012 11:09 pm
Posts: 187
Location: Portage le Prairie, Manitoba
Those holes rang a bell! Maybe I've read about them somewhere? :? Either way, I was certain that Hammarlund must have incorporated some sort of way to gauge the alignment of the turret. Not that I needed it that badly!

Here's a pic of the turret position relative to the holes from eyeballing it alone:

Image

Look how close that is! That's my proudest moment in this restoration thus far! :P

Anyway, the RF deck has been reinstalled. I cleaned the contact fingers with Deoxit before I put it back in. And yes, I was constantly checking the alignment access holes during the recap process to ensure that they were clear of obstructions.

My first SP-600 RF deck rebuild and it was just as hellish yet somehow enjoyable as everyone described it! I'm just glad I have a desoldering iron. It would've been a nightmare without one! In fact, during the recap I was using two different irons and my Hakko desoldering iron and when reinstalling it, I used a different iron with a curved tip to help get into the tight space between the RF deck and the variable capacitor. Those 16 wires to the VC seem a little excessive! :P

Here's a pic of the radio at the moment:

Image

It's starting to look like a radio again! I just wish I could've fired her up after reinstalling the RF deck. I have had many radios in my short life, and I have a few at the moment, but none quite like this. She definitely seems like a champion band cruiser! I very much look forward to finding out.

You guys may notice that I replaced the replacement BNC connector with an N connector. No particular reason why. That's just what I had. Until lately, I never appreciated the solid, tight feel of the humble N connector. The connector is an old US Navy silver plated type that is as old as this radio, it just seemed fitting.

I noticed something on the RF deck that I had not noticed before. Or more likely, I noticed it but I didn't comprehend it at the time.

Image

I just love seeing those little orange Signal Corps stamps! If a radio has that stamp on it, chances are I'll like it! That's part of the reason I didn't clean up the steel at all. I didn't want to ruin the vintage stamp!

Plenty more to do and plenty more to come. But for now, I should head to bed. I'll need this radio to help heat my house soon! Winter came earlier this year than the last few. Last year, it was almost double digits on Remembrance Day, and this year it'll be a -25 wind chill and half a foot of snow on the ground!

I hope you're all enjoying your local weather as much as I am!

_________________
I hope my pictures aren't too big...


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Tue 07, 2017 5:48 am 
Member
User avatar

Joined: Jan Thu 01, 1970 1:00 am
Posts: 31406
Location: Maryland 20709, USA
Hi towble,

Marvelous job.

You have much greater patience than I. My compliments.

- Leigh

_________________
73 de Leigh W3NLB
http://www.AtwaterKent.info
Click "Grebe Stuff" for Synchrophase info


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Tue 07, 2017 5:50 am 
Member

Joined: Dec Mon 31, 2012 11:09 pm
Posts: 187
Location: Portage le Prairie, Manitoba
Oh, and I forgot! Thanks for all the hints and reminders and such everyone! I can be pretty forgetful, so they certainly help! :mrgreen:

How so, Leigh?

_________________
I hope my pictures aren't too big...


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Wed 08, 2017 11:52 pm 
Member

Joined: Dec Mon 31, 2012 11:09 pm
Posts: 187
Location: Portage le Prairie, Manitoba
I forgot something!

Nothing super important or anything. I just meant to give the RF deck a good cleaning with compressed air before I reinstalled it. I think it'll be alright though.

_________________
I hope my pictures aren't too big...


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Thu 09, 2017 12:30 am 
Member
User avatar

Joined: Sep Wed 10, 2014 2:01 am
Posts: 1463
Location: Costa Mesa, California
Towble,

The third time I put my RF deck back in the radio, I made sure all the connections were absolutely ready to go for a fourth or fifth time. That pretty much guaranteed I would not need those extra times. With tube base extenders a person can test the pins of the RF deck tubes without needing access below. Unfortunately, when a tube plate comes up with no B+ . . . . Then you need to really be sure it isn't the result of something not below the deck.

Norm

_________________
KK6IYM


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Thu 09, 2017 3:41 am 
Member

Joined: Dec Mon 31, 2012 11:09 pm
Posts: 187
Location: Portage le Prairie, Manitoba
Norm Johnson wrote:
Towble,

The third time I put my RF deck back in the radio, I made sure all the connections were absolutely ready to go for a fourth or fifth time. That pretty much guaranteed I would not need those extra times. With tube base extenders a person can test the pins of the RF deck tubes without needing access below. Unfortunately, when a tube plate comes up with no B+ . . . . Then you need to really be sure it isn't the result of something not below the deck.

Norm


I hope I don't end up having to remove it again, but I might. I'd really like to get some of those extenders! But from what I've seen, they're not all that common and when you do find them, they're not cheap. I have some plugs for 4,5,7,8, and 9 pin tube sockets, I could make my own extenders. I just need to find the plugs.

_________________
I hope my pictures aren't too big...


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Thu 09, 2017 7:32 am 
Member

Joined: Jul Thu 29, 2010 5:35 am
Posts: 830
Location: Simonton, Texas
I have purchased 7 and 9 pin tube extenders on ebay at very reasonable prices. ($10.00 to $15.00) for 2. They don't seem to come up very often.

_________________
Knowledge is useless unless you can share it. KA5OBI


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Tue 14, 2017 7:48 am 
Member

Joined: Dec Mon 31, 2012 11:09 pm
Posts: 187
Location: Portage le Prairie, Manitoba
Koby wrote:
I have purchased 7 and 9 pin tube extenders on ebay at very reasonable prices. ($10.00 to $15.00) for 2. They don't seem to come up very often.


I've seen them come up now and then, but all the times I've seen them, they sold for quite a bit. I think I will make my own if I find I need them.

It's been a while since I posted an update. I had a few busy days with my family insisting on celebrating my birthday...twice. I won $2 on a scratch ticket and used that to buy a 2nd scratch ticket, then won $2 on that one! I'm gonna put that towards another scratch ticket and I'm hoping I'll win at least $5 on that one! :P

Anyway, not much has been done to the radio since my last post. All I've done is replace the four capacitors in the IF transformers as well as clean up and reinstall their respective cans.

Here's a before pic:

Image

And here's an after pic showing the new caps:

Image

I can really see why they call them black beauty capacitors. They brighten things up very nicely! The replacement caps are not all that pretty. I also found some other .01uf caps I have that are about 1/4 the size of these Panasonic ones I am using despite having the same voltage ratings. I have to say, I'm a little skeptical of them though. I can't remember where I got them or what brand they are. I think I got them from Antique Electronic Supply a few years ago.

Anyway, here's a pic of the radio as it looks right now:

Image

Still a lot to go. I'm right around that part in a restoration where I start to get bored. So I have to push through it and get the receiver working. That'll get me excited all over again and help me through the rest of it. My attention span is not the greatest. I find myself interested in too many things and tend to get sidetracked.

For example, I've recently been struck with an interest in amateur chemistry. I find myself especially intrigued by the glassware. All those different parts and their functions. I bought a few dozen pieces from China on eBay. I know that some places like Australia and Texas are pretty strict about people acquiring laboratory glassware. I'm not sure how it is here in Canada, I just hope the police don't suspect me of anything and feel the need to knock down my door. :roll:

Anyway, I guess I'll be moving on to the underside of the chassis soon. I really have to take a close look at things and make sure everything is wired correctly. Then once the power supply has been rebuilt, I'll be ready to fire this old girl up!

_________________
I hope my pictures aren't too big...


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Tue 14, 2017 12:14 pm 
Member

Joined: Oct Sun 15, 2006 12:57 pm
Posts: 5319
Quote:
...attention span is not the greatest...AND...interested in too many things
I suspect there are a number of folks here that suffer from that affliction.

And, speaking of glassware, I bought this little test tube rack and tubes off the bay to store diodes, Zeners mostly, and, tap and drill "sets" for easy reference.

Image

Image

Image

_________________
Bold text & pics are usually links.

Mike


Last edited by Mikeinkcmo on Nov Tue 14, 2017 12:22 pm, edited 1 time in total.

Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Tue 14, 2017 12:15 pm 
Member

Joined: Oct Sun 15, 2006 12:57 pm
Posts: 5319
:mrgreen: OOPS :mrgreen:

_________________
Bold text & pics are usually links.

Mike


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Tue 14, 2017 7:02 pm 
Member

Joined: Dec Mon 31, 2012 11:09 pm
Posts: 187
Location: Portage le Prairie, Manitoba
Mikeinkcmo wrote:
And, speaking of glassware, I bought this little test tube rack and tubes off the bay to store diodes, Zeners mostly, and, tap and drill "sets" for easy reference.


I've heard of people doing that before. Test tubes are actually about the only thing I didn't buy, but I'm thinking I will get a set eventually. They certainly would be useful for sorting stuff if nothing else.

_________________
I hope my pictures aren't too big...


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Wed 15, 2017 4:42 pm 
Member
User avatar

Joined: Feb Sat 28, 2015 8:37 pm
Posts: 452
Location: Walker, MI
Let's see here, diodes in tubes are those now called 5U4? Lol


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Wed 15, 2017 5:47 pm 
Member
User avatar

Joined: Jun Sun 19, 2011 2:31 pm
Posts: 4802
Mike,

Great storage idea and it looks like a very neat solution to the storage problem.

Just don't drop and break them. In the 9th grade the chem teacher was a former college prof who had moved from Canada to take care of a relative on the Mississippi gulf coast. On the first day of class he made a big point out of not breaking any of the pyrex test tubes because he had gone through a lot to get the school to purchase them. Seconds later, my lab partner who i had known since the first grade, dropped the tube she was holding. The breaking sound was followed by dead silence and then the teacher/prof slammed an entire carton of them on the floor and stormed out. I figured I was going to be toast also due to guilt through association.

He turned out to be the best of a very good group of teachers I experienced in high school but to say he had a temper would be putting it mildly. But he was generally very nice in class and had a pretty decent sense of humor. A couple of weeks later my lab partner accidentally set her long hair on fire with the Bunsen burner and he referred to that event as "the revenge of the test tubes". He also told me maybe I was a little too hasty in putting out the fire :)

Rodger WQ9E


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Thu 16, 2017 5:08 am 
Member

Joined: Oct Sun 15, 2006 12:57 pm
Posts: 5319
Funny story Rodger, but these are plastic so I don't have to worry about breakage.

I think I only paid something like 9 bucks, on the bay, for the whole lot, including the rack.

_________________
Bold text & pics are usually links.

Mike


Top
 Profile  
 
 Post subject: Re: Hammarlund SP-600 JX-7 Restoration
PostPosted: Nov Thu 16, 2017 1:22 pm 
Member
User avatar

Joined: Jun Sun 19, 2011 2:31 pm
Posts: 4802
Excellent price Mike and after that experience I will always cringe a little when I see a nice test tube.

Rodger WQ9E


Top
 Profile  
 
Post New Topic Post Reply  [ 76 posts ]  Moderator: Sandy Go to page Previous  1, 2, 3, 4

All times are UTC [ DST ]


Who is online

Users browsing this forum: No registered users and 8 guests



Search for:
Jump to:  


















Privacy Policy :: Powered by phpBB